内容发布更新时间 : 2024/5/11 0:24:03星期一 下面是文章的全部内容请认真阅读。

if absinc = zero, refht_a, !refht_i else, refht_i, !refht_a

pdrill #钻孔固定循环 pdrlcommonb

pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, dwell, *feed, strcantext, e pcom_movea

ppeck #啄式钻孔固定循环 pdrlcommonb

pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *peck1, *feed, strcantext, e pcom_movea

pchpbrk #断屑固定循环 pdrlcommonb

pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *peck1, *feed, strcantext, e pcom_movea

ptap #攻螺纹固定循环 pdrlcommonb

pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *feed, strcantext, e pcom_movea

pbore1 #镗孔固定循环 #1 pdrlcommonb

pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, dwell, *feed, strcantext, e pcom_movea

pbore2 #镗孔固定循环 #2 pdrlcommonb

pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *feed, strcantext, e pcom_movea

pmisc1 #Canned Misc #1 Cycle pdrlcommonb

pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, shftdrl, dwell, *feed, strcantext, e pcom_movea

pmisc2 #Canned Misc #2 Cycle (User Option) pdrill

31

pdrill_2 #Canned Drill Cycle, additional points pdrlcommonb

pcan1, pbld, n, pxout, pyout, pzout, prdrlout, dwell, feed, strcantext, e pcom_movea

ppeck_2 #Canned Peck Drill Cycle pdrill_2

pchpbrk_2 #Canned Chip Break Cycle pdrill_2

ptap_2 #Canned Tap Cycle pdrill_2

pbore1_2 #Canned Bore #1 Cycle pdrill_2

pbore2_2 #Canned Bore #2 Cycle pdrill_2

pmisc1_2 #Canned Misc #1 Cycle pdrill_2

pmisc2_2 #Canned Misc #2 Cycle pdrill_2

pdrlcst #自定义钻孔循环 8 - 19 (user option)

#Use this postblock to customize drilling cycles 8 - 19 pdrlcommonb

\ pcom_movea

pdrlcst_2 #自定义钻孔循环 8 - 19, additional points (user option) #Use this postblock to customize drilling cycles 8 - 19 pdrlcommonb

\ pcom_movea

pcanceldc #Cancel canned drill cycle result = newfs (three, zinc) z = initht

prv_zia = initht pxyzcout !zabs, !zinc

prv_gcode = zero

32

pbld, n, \

# -------------------------------------------------------------------------- # Canned Text

# -------------------------------------------------------------------------- pcan #Canned text - before output call strcantext = sblank if cant_no > zero, [

if cant_pos1 = zero, pcant_1 if cant_pos2 = zero, pcant_2 if cant_pos3 = zero, pcant_3 if cant_pos4 = zero, pcant_4 if cant_pos5 = zero, pcant_5 if cant_pos6 = zero, pcant_6 if cant_pos7 = zero, pcant_7 if cant_pos8 = zero, pcant_8 if cant_pos9 = zero, pcant_9 if cant_pos10 = zero, pcant_10 pbld, n, strcantext, e strcantext = sblank ]

pcan1 #Canned text - with move strcantext = sblank if cant_no > zero, [

if cant_pos1 = one, pcant_1 if cant_pos2 = one, pcant_2 if cant_pos3 = one, pcant_3 if cant_pos4 = one, pcant_4 if cant_pos5 = one, pcant_5 if cant_pos6 = one, pcant_6 if cant_pos7 = one, pcant_7 if cant_pos8 = one, pcant_8 if cant_pos9 = one, pcant_9 if cant_pos10 = one, pcant_10 ]

if cstop, strcantext = strcantext + sm00 if cgstop, strcantext = strcantext + sm01

#Output of strcantext occurs at the end of the output line

pcan2 #Canned text - after output call strcantext = sblank if cant_no > zero, [

if cant_pos1 = two, pcant_1

33

if cant_pos2 = two, pcant_2 if cant_pos3 = two, pcant_3 if cant_pos4 = two, pcant_4 if cant_pos5 = two, pcant_5 if cant_pos6 = two, pcant_6 if cant_pos7 = two, pcant_7 if cant_pos8 = two, pcant_8 if cant_pos9 = two, pcant_9 if cant_pos10 = two, pcant_10 pbld, n, strcantext, e strcantext = sblank ]

pcant_1 #Canned text - output call cantext = cant_val1 pcant_out

pcant_2 #Canned text - output call cantext = cant_val2 pcant_out

pcant_3 #Canned text - output call cantext = cant_val3 pcant_out

pcant_4 #Canned text - output call cantext = cant_val4 pcant_out

pcant_5 #Canned text - output call cantext = cant_val5 pcant_out

pcant_6 #Canned text - output call cantext = cant_val6 pcant_out

pcant_7 #Canned text - output call cantext = cant_val7 pcant_out

pcant_8 #Canned text - output call cantext = cant_val8 pcant_out

pcant_9 #Canned text - output call cantext = cant_val9

34

pcant_out

pcant_10 #Canned text - output call cantext = cant_val10 pcant_out

pcant_out #Canned text - build the string for output #Assign string select type outputs if cantext = three, bld = one if cantext = four, bld = zero #Build the cantext string

if cantext = one, strcantext = strcantext + sm00 if cantext = two, strcantext = strcantext + sm01 if cantext > four, [

strtextno = no2str(cantext)

strcantext = strcantext + strm + strtextno ]

# -------------------------------------------------------------------------- # 坐标计算，通常不需要修改

# -------------------------------------------------------------------------- pxyzcout #Map coordinates xabs = vequ (x) feed = fr_pos

if feed > maxfeedpm, feed = maxfeedpm

#Incremental calculations

ps_inc_calc #Incremental calculations, start xia = fmtrnd(xabs) yia = fmtrnd(yabs) zia = fmtrnd(zabs)

xinc = vsub (xia, prv_xia)

pe_inc_calc #Incremental calculations, end !xia, !yia, !zia !x, !y, !z

# -------------------------------------------------------------------------- # Numbered questions for Mastercam Version 8

# -------------------------------------------------------------------------- 38. 快速进给率? 300.0 #76. 配置文件名?

80. 接收和发送的通信端口号 (1 or 2) ? 2

81. 传输速率 (110,150,300,600,1200,2400,4800,9600,14400,19200,38400)? 9600 82. 奇偶校验 (E/O/N)? E 83. 数据位 (7 or 8)? 7

35